Top Standards Worldwide
British Standards  More... BS 8558-2011 guide to the design, installation, testing and maintenance of services supplying water for domestic use within buildings and their curtilages – complementary guidance to bs en 806 BS EN 15341-2007 Maintenance - Maintenance key performance indicators BS EN 61131-2-2008 programmable controllers part 2: equipment requirements and tests BS EN ISO 17637-2011 non-destructive testing of welds-visual testing of fusion-welded joints (iso 17637:2003) BS 2059-1953 Specification for straight-sided splines and serrations	Japanese Standards Association (JSA JIS)  More... JIS D 2001-1959 involute spline for automobiles JIS G 3539-1991 carbon steel wires for cold heading and cold forging errata: 3/2003 r(1997) JIS A 5335-1987 pretensioned spun concrete piles JIS L 1041-2011 test methods for resin finished textiles JIS B0403-1995 Castings -- System of dimensional tolerances and machining allowances	Electrical and Electronics Engineers, Inc. (IEEE)  More... IEEE STD 81-2012 measuring earth resistivity, ground impedance, and earth surface potentials of a grounding system IEEE C57.13.1-2006 guide for field testing of relaying current transformers IEEE 1003.13-2003 standard for information technologystandardized application environment profile (aep)posix realtime and embedded application support ieee computer society document IEEE 693-2005 recommended practice for seismic design of substations IEEE 835-1994 (Power cable ampacity tables)	International Organization for Standardization (ISO)  More... ISO 3833-1977 Road vehicles; Types; Terms and definitions ISO 612-1978 road vehicles; dimensions of motor vehicles and towed vehicles; terms and definitions ISO 18593-2004 Microbiology of food and animal feeding stuffs - Horizontal methods for sampling techniques from surfaces using contact plates and swabs ISO 898-1-2013 mechanical properties of fasteners made of carbon steel and alloy steel -- part 1: bolts, screws and studs with specified property classes -- coarse thread and fine pitch thread ISO 2685-1998 Aircraft - Environmental test procedure for airborne equipment - Resistance to fire in designated fire zones
International Electrotechnical Commission (IEC)  More... IEC 60364-5-52 CORR 1-2011 Low-voltage electrical installations. Part 5-52:Selection and erection of electrical equipment. Wiring systems CORRIGENDUM 1 Installations électriques. basse tension. Partie 5-52:Choix et mise en oeuvre des matériels électriques. Canalisations CORRIGENDUM 1 Edition 3.0 IEC 62402-2007 Obsolescence management - Application guide IEC 60205 Edition 3.1-2009 Calculation of the effective parameters of magnetic piece parts IEC 60949-1988 Calculation of thermally permissible short-circuit currents, taking into account non-adiabatic heating effects IEC 60757-1983 Code for designation of colours	Australia Standards(AS)  More... AS 4991-2004 lifting devices AS 1692-2006 steel tanks for flammable and combustible liquids AS/NZS 2918-2001 domestic solid fuel burning appliances - installation AS 2067-2008 substations and high voltage installations exceeding 1 kv a.c. AS/NZS 3008.1.1-2009 electrical installations - selection of cables - cables for alternating voltages up to and including 0.6/1 kv - typical australian installation conditions	Canadian Standards Association(CSA)  More... CSA Z797-09-2009 code of practice for access scaffold first edition CSA W178.2-08-2008 certification of welding inspectors fifth edition CSA B149.1-10-2010 natural gas and propane installation code fourteenth edition CSA B167-08-2008 overhead travelling cranes design, inspection, testing, maintenance, and safe operation third edition CSA C282-09-2009 emergency electrical power supply for buildings fifth edition	Francaise de Normalisation(NF)  More... NF E22-141-1955 cylindrical involute splines. classification index : e22-141 NF A32-054-2005 steel castings for general engineering uses. NF ISO 7954-1988 microbiology. general guidance for enumeration of yeasts and moulds. colony count technique at 25 degrees c. microbiologie. directives gales pour le dombrement des levures et moisissures. technique par comptage des colonies 25 degr celsius. NF E81-010-1990 (PUNCHING AND STAMPING. BURR ON BLANKED OR PUNCHED METALLIC PARTS. MAXIMUM ALLOWABLE BURR HEIGHT AND MEASURING METHOD.) NF V08-408-1997 (MICROBIOLOGY OF FOOD AND ANIMAL FEEDING STUFFS. CONTROL OF STABILITY OF PRESERVED AND ASSIMILATED PRODUCTS. ROUTINE METHOD.)

Top American Standards
American Society for Testing Material (ASTM)   More... ASTM D 907-2008 standard terminology of adhesives ASTM D 6951-2003 standard test method for use of the dynamic cone penetrometer in shallow pavement applications ASTM UOP 779-1992 chloride in petroleum distillates by microcoulometry ASTM E415-2008 Standard Test Method for Atomic Emission Vacuum Spectrometric Analysis of Carbon and Low-Alloy Steel ASTM D 5227-2001 standard test method for measurement of hexane extractable content of polyolefins	Underwriters Laboratories (UL)  More... UL 583-2012 standard for electric-battery-powered industrial trucks UL 1439-1998 (Tests for sharpness of edges on equipment UL 2580-2011 standard for batteries for use in electric vehicles UL 142-2006 standard for steel aboveground tanks for flammable and combustible liquids UL 467-1993 (Grounding and bonding equipment	American National Standards Institute (ANSI)  More... ANSI/ISA 5.1-2009 Instrumentation Symbols and Identification ANSI B 92.1-1996 involute splines and inspection ANSI A58.1-1982 American National Standard Minimum Design Loads for Buildings and Other Structures ANSI/ANS 3.1-1993 Selection, Qualification, and Training of Personnel for Nuclear Power Plants ANSI/AWS D14.1/D 14.1M-2005 Specification for Welding of Industrial and Mill Cranes and Other Material Handling Equipment	Society of Automotive Engineers(SAE)  More... SAE AS9131 REV C-2012 (r) aerospace series - quality management systems - nonconformance data definition and documentation SAE J639-2011 (r) safety standards for motor vehicle refrigerant vapor compression systems SAE J498B-1987 involute splines, serrations, and inspection SAE J1459-2009 v-ribbed belts and pulleys SAE AMS 2759/9-1996 hydrogen embrittlement relief baking of steel parts